Maytag Washer Repair in Tampa Bay
We fix Maytag washers at your home in Pasco, Hillsborough and Pinellas counties. Call with the model number and the error code, if there is one, and the technician will bring parts that fit.
Fix Now Appliance is an independent repair company, not affiliated with or authorized by Maytag. Maytag is a trademark of its owner, used here only to describe the appliances we repair.
Maytag washer error codes
What the code on the display usually means. Codes differ between models and years, so if yours isn't here or the meaning doesn't match, call and read it to us.
| Code | What it usually means |
|---|---|
| F01 | Electronic control board error: failure in the machine's main control unit. |
| F02 | Long drain time: machine is taking too long to drain. Often a clog in the drain system. |
| F05 | Water temperature sensor error: issue with the sensor that monitors water temperature. |
| F07 | Motor control unit error: problem with the motor control board. |
| F09 | Overflow condition: machine is detecting an overflow or excessive water in the tub. |
| F11 | Communication error between the central control unit and the motor control unit: failure in the communication link. |
| F21 | Drain problem: potential issue with the drain system, possibly a clog or a kinked drain hose. |
| F28 | Serial communication error: communication failure between the main control board and the motor control board. |
| F51 | Rotor position sensor failure: issue with the sensor that detects the position of the washer's motor rotor. |
Common Maytag washer problems
Won't drain
A sock or coin stuck in the drain pump, a clogged pump filter or a kinked drain hose. Sometimes the pump motor itself has failed.
Won't spin, or spins slowly
Often a drain problem, because a washer won't spin with water in the drum. Otherwise a worn drive belt, motor coupling, lid switch or door lock.
Leaking
On front-loaders, a torn door boot or a loose pump hose. On top-loaders, a failed tub seal or a worn inlet hose.
Shaking or banging during spin
Worn shock absorbers or suspension rods, or a load that's badly out of balance.
Check these before you call
If one of these fixes it, you don't need us.
- Clean the pump filter. On most front-loaders it sits behind a small door at the bottom front.
- Make sure both water taps behind the washer are fully open.
- Check that the drain hose isn't kinked behind the machine or pushed too far into the standpipe.
- If it only smells, run an empty hot cycle with washer cleaner before calling anyone.
Repair or replace?
A failed transmission on an older top-loader or a worn drum bearing on a front-loader can cost close to a new machine. We'll tell you the price before you spend anything.
Three steps, no surprises
- 1
Call or send a request
Tell us the brand, model and what's wrong. The technician brings the parts most likely needed.
- 2
Get a firm price
We find the fault and quote the exact cost before touching anything. The diagnostic is $89, and it comes off the bill if you go ahead with the repair.
- 3
Fixed and tested
Most repairs are done on the same visit. You pay after it's tested in front of you and get a written warranty.
Tell us what's wrong
Send the form and we'll call you back during business hours. In a hurry? Calling is faster.
(727) 425-27077 days a week, 8 AM–6 PM
fixnowappliance@gmail.comMaytag washer repair questions
Are you an authorized Maytag service center?
No. Fix Now Appliance is an independent repair company, not affiliated with Maytag. If your Maytag washer is still under the manufacturer's warranty, call Maytag first, because their warranty repair is free. Once it's out of warranty, we can fix it.
Why does my front-loader smell?
Water and detergent stay in the door boot and the drain. Wipe the boot, leave the door open after washing and use the right amount of HE detergent. If the smell stays, the pump filter or drain may need cleaning.
Can you fix a washer that's still under warranty?
Call the manufacturer first, because their repair is free. We can help once the warranty is over.
Something stopped working?
7 days a week, 8 AM–6 PM. Most repairs done on the first visit.